Analysis of Sudden Quality Problems in the Spinning Process

2026-09-03

The spinning process involves a wide variety of accessories and components in large quantities. It is also affected by complex factors such as operations, processing techniques, and air conditioning systems. These factors can easily lead to unexpected accidents and cause sudden quality issues. The following is a brief explanation and analysis from four perspectives:


I. Sudden Quality Problems Caused by Poor Equipment Condition


1. Damage to Front Aprons (Front Rubber Rollers)


Damage to front aprons is a common accessory issue in the ring spinning process, often appearing as localized biting marks or grooves running around the entire circumference. When the damage is severe, the affected areas cannot effectively grip and control the fibers during the drafting process, leading to a significant deterioration in yarn quality.


2. Loss of Pressure in Top Apron Springs


Severe wrapping of yarn around the rollers and aprons can cause a loss of pressure in the top apron springs. This prevents the top and bottom aprons from forming an elastic nip. In severe cases, the top apron will lift up, causing a "floating apron" phenomenon. This completely results in a loss of fiber control, generating severe drafting waves. This not only worsens the yarn evenness but also causes severe long thick and long thin places.


3. Poor Operation of the Top Apron


The main causes of poor top apron operation include fiber accumulation inside the top apron and apron, loss of pressure in the middle-top roller, or deformation of the top apron. When the top apron operates poorly, the roving in the back zone becomes slack. Due to the lack of pre-drafting in the back zone, the roving entering the front zone remains relatively slack. During drafting, the frictional cohesion and control force between fibers are weakened, leading to deteriorated evenness and increased drafting efficiency. This results in a smaller yarn count (producing off-count yarn) and long thin horizontal stripes on the fabric surface.


In addition to the above defects, severe malfunction of the top apron can cause periodic sticking. This periodically affects the drafting of fibers in the back zone by the drafting nip formed by the top and bottom aprons. The mechanical waves generated in the back zone are amplified by the front zone drafting, resulting in a longer wavelength. The wavelength depends on the sticking cycle of the apron, as well as the draft multiples of the front and back zones.


4. Transmission Component Failures


Transmission component failures mainly refer to damage to transmission gears, shafts, and pins. Once such mechanical failures occur, they will cause quality problems for the entire yarn batch, resulting in a significant impact. Therefore, high attention must be paid to this issue. To address transmission component failures, it is essential to strengthen daily cleaning, maintenance, and upkeep, especially the inspection of key components.


II. Quality Problems Caused by Improper Operations


1. Off-Count Yarn Generated During Piecing


When operators start a new yarn end during the spinning of a new variety or after doffing, they habitually use yarn they carry with them for piecing. If the piecing yarn differs in count or composition from the yarn being spun, off-count yarn will be generated. Although the length of off-count yarn is short, its impact on product quality is even greater than that of a full cop of wrong-count yarn. Piecing off-count yarn has two distinct characteristics: First, there is a large quantity and wide distribution. Especially when spinning a new variety, to speed up piecing, most operators usually piece together, leading to large-scale off-count phenomena. Second, the cause is very hidden and prone to recurrence, making it difficult for management to detect. Off-count yarn of different counts will produce long thick and thin places on the fabric, while off-count yarn of different compositions will cause horizontal stripes after dyeing due to the different dyeing properties of the fibers.


To solve the problem of piecing off-count yarn, first, operators' quality awareness must be strengthened, and they must not randomly use yarn of different varieties for piecing. Second, dedicated piecing yarn should be prepared in advance for newly spun varieties. Third, for varieties with significant differences in fiber composition, it is best to produce them in separate workshops or adopt isolation measures, assigning operators to specific varieties. Fourth, it is imperative to thoroughly clean any leftover yarn of different varieties from the bobbins.


2. Low-Twist Yarn Generated During Doffing and Spindle Base Cleaning


When operators clean the spindle base or manually pull yarn for doffing, improper operation can easily cause the spindle tape to fall off the spindle wharve and get caught on the edge of the larger-diameter wharve. Since the diameter of the wharve edge is larger than the spindle wharve, the corresponding spindle speed will be slower than normal, resulting in reduced yarn twist and generating low-twist phenomena. Tests show that when the spindle tape deviates, the corresponding yarn twist will decrease by 15%~20%. The yarn properties will change significantly, the yarn structure will become loose, and obvious horizontal stripes will appear after weaving and dyeing. To reduce such low-twist yarn, operators' quality awareness should be strengthened, and special inspections and assessments should be enhanced in the workshop. When cleaning spindle bases, it is best not to use brushes; instead, use a twist gun to extract waste and fly.


share